PT4115 PDF

PT – LED Driver with Dimming. PTB89E Package SOT PT – LED Driver with Dimming Downloads. PT Datasheet. Description. LEDs need constant current, for example normal LED has mA constant current, but V varying voltage, this board do this kind of work. So I built a pt circuit to control my LEDs! it has a Ohm resistor so it should give me ~ma of current!.

Author: Kibei Voodoolmaran
Country: Namibia
Language: English (Spanish)
Genre: Technology
Published (Last): 9 June 2013
Pages: 377
PDF File Size: 13.77 Mb
ePub File Size: 5.58 Mb
ISBN: 999-9-15684-906-6
Downloads: 70139
Price: Free* [*Free Regsitration Required]
Uploader: Zolomi

Ebay has a ton of them, but I never tried them yet. Why is that chip heating like that? Post as a guest Name. Feb 4, Yes I know transfer method. Yes, my password is: By clicking “Post Your Answer”, you acknowledge that you have read our updated terms of serviceprivacy policy and cookie policyand that your continued use of the website is subject to these policies. The inductor is also a long way from the chip and Vin also crosses v-out The sparks are inductor’s way to keep the current on if all low voltage drop routes are off.

Making an answer out of my comment: Below is the schematic and the PCB board: I tried with higher value resistor, but it’s still burning. Gives You both the time to make secure meassurements and the ease to identify where the problem really is. It is particularly important to mount the coil and the input decoupling capacitor as close to the device pins as possible to minimize parasitic resistance and inductance, which will degrade efficiency.

Related Posts  ATMEGA88PA PDF

I wish I had local parts shops. Post Your Answer Discard By clicking “Post Your Answer”, you acknowledge that you have read our updated terms of serviceprivacy policy and cookie policyand that your continued use of the website is subject to these policies. I made some pics. A oscillator might be able to control that.

By using our site, you acknowledge that you have read and understand our Cookie PolicyPrivacy Policyand our Terms of Service. Home Questions Tags Users Unanswered. I checked every pin of the IC and didn’t find any short or something wrong. By clicking “Post Your Answer”, you acknowledge that you have read our updated terms of serviceprivacy policy and cookie policyand that your continued use of the website is subject to these policies.

dc dc converter – PT LED driver – Electrical Engineering Stack Exchange

See also “Layout considerations” on page 14 of the datasheet. But, only for a few sec, then it’s starting to burn I have used 0. That current sense line loops around the chip, crosses and runs parallel with the drive line. I recorded it by my mobile phone. Also, what are you feeding to the DIM pin? Why are you using a resistor as the load? Increase the value of the Rs until You have sorted out what the problem really is.

Plus the heat and current problems. Is there any kind of chart with this PT for coil and resistor ratings?

I’m not impressed with this chip as everything goes through it to ground. So I won’t destroy more circuits. Sign up or log in Sign up using Google. That indicates that the problem is the flux.

Related Posts  NAVCOMPT FORM 2276A PDF

I have no experience with buck convertors, what can be wrong? Do you already have an account? Last chance;] I’m just hoping, the problem was a DC supply. It showed about mA. The PT needs to be turned round degrees with that part layout. If you see a short then we can say that the IC is broken.

The chip is rated up to 5 volts in battery power which it can double with pt44115 input and discharge limiting. Pt115 made another pcb.

PT’s pad is in front of R1. Before I was putting the chip correctly. The datasheet also cautions against using a silicon diode for D3 called D1 or D in the datasheetbecause poor reverse recovery time and high voltage drop can cause high voltages to appear on the SW pin. This is actually funny, but I burned the last chip But in truth the whole layout needs redone. That’s a real problem – the acid is not only highly conductive but it’s also corrosive.

Can you give a schematic of your circuit? Jan 20, 74 4.

PT4115 Led diver

I will check your routing once I get home. I’ve had ma through a garden lamp F 4 pin chip, but that was by accident testing an LED in circuit. I didn’t connect it correctly. When I turn it off its making a short. P4t115 are you sure that diode is not fried.